ABSTRACT Geothermal energy is a renewable source that can assist in the thermal conditioning of constructed environments. The objective of this study was to analyze the heat transfer in a Red Latosol (Oxisol), in heat storage process, using two linear heat exchangers. The treatments were arranged in a 3 × 2 × 3 factorial scheme, corresponding to three temperature differentials between soil and water (5, 10 and 15 °C), two types of materials (PVC and copper) and three radial distances (10, 20 and 25 cm), with three replicates. Soil temperature variations were obtained continuously for a period of 12 hours using DS18B20 sensors. These variations were logarithmic as a function of heat transfer time and radial distance and linear as a function of the temperature differential between soil and water (θ). The temperature differential between soil and water was the main factor that influenced soil temperature variation, and the material employed was insignificant in this variation. The minimum distance between heat exchangers should be greater than 50 cm, and PVC pipes proved to be more attractive for use involving thermal exchange with the ground as they are more viable than copper and easier to implement.

RESUMO A energia geotérmica é uma fonte renovável que pode auxiliar no condicionamento térmico de ambientes construídos. O objetivo deste estudo foi analisar a transferência de calor em um Latossolo Vermelho (Oxisol), em processo de armazenamento de calor, utilizando dois trocadores de calor lineares. Os tratamentos foram dispostos em esquema fatorial 3 × 2 × 3, correspondendo a três diferenciais de temperatura entre solo e água (5, 10 e 15 °C), dois tipos de materiais (PVC e cobre) e três distâncias radiais (10, 20 e 25 cm), com três repetições. As variações de temperatura do solo foram obtidas continuamente por um período de 12 horas usando sensores DS18B20. Essas variações foram logarítmicas em função do tempo de transferência de calor e da distância radial, e lineares em função do diferencial de temperatura entre o solo e a água (θ). O diferencial de temperatura entre o solo e a água foi o principal fator que influenciou na variação da temperatura do solo, sendo que o material empregado foi insignificante nessa variação. A distância mínima entre os trocadores de calor deve ser maior que 50 cm, e os tubos de PVC se mostraram mais atrativos para uso envolvendo troca térmica com o solo por serem mais viáveis que os de cobre e mais fáceis de serem executados.

ABSTRACT Materials from renewable sources have been increasingly used in construction to assist in sustainable development. Therefore, the use of timber becomes an environmentally advantageous solution, especially if used for long-term purposes, such as in structures. In this sense, this study aimed to evaluate the performance of glued-laminated timber frames reinforced in their main connections. The structures were made using timber from the Araucaria angustifolia species and polyurethane adhesive based on vegetable oils. The frames, on a reduced scale, had a pillar height and free span of 2 m and were reinforced in the connections between the roof beams and pillars. The rupture strength values of the structures averaged 38.02 kN, approximately 5.47 times the design load, and represented a 32% increase in strength compared to non-reinforced structures. The displacements did not reach the normative limit for the design load and presented a linear behavior for strengths higher than three times those of the design. The structures presented satisfactory structural behavior and had an improvement in resistance and rigidity caused by the addition of reinforcements.

ABSTRACT This study evaluated the electrical performance of a photovoltaic-thermal (PVT) system using water as a cooling fluid (PVT/w), with adaptation, in a photovoltaic module of a device for heating water without direct contact with the cell and with air as the secondary working fluid. The PVT/w system with forced and natural circulation was compared in a regime of thermal accumulation of hot water and supply by a boiler reservoir relative to the same PV panel with the original factory characteristics. The average system temperature, open circuit voltage, current and voltage with load, and generated electric power were analyzed during seven non-consecutive days, with ten repetitions every thirty minutes between 9:30 am and 2:00 pm in the city of Dourados-MS, Brazil, between June and July 2021. The PVT system with forced circulation (PVT/w_CB) presented the best electrical performance compared to the PVT system with natural circulation (PVT/w_SB), in the order of 3.7%.

RESUMO O processo de secagem de grãos é uma prática comum e necessária à manutenção da qualidade, porém é uma das atividades de maior demanda energética dentre as fases pós-colheita. Neste contexto, realizou-se este estudo com objetivo de avaliar os efeitos de diferentes períodos de repouso na eficiência energética do processo de secagem e manutenção da integridade das membranas dos grãos colhidos com teor de água de 0,34 ± 0,01 b.s. Os grãos foram secos em um secador experimental de camada fixa com controle de temperatura e fluxo de ar. O experimento foi montado em delineamento inteiramente casualizado, com cinco períodos de repouso (0, 4, 8, 12 e 16 horas) e quatro repetições, em que zero corresponde à secagem contínua e os demais à secagem intermitente. Os grãos foram secos a 100 ºC de temperatura e fluxo de ar de 15,4 m3 min-1 t-1 até atingir 0,16 ± 0,02 b.s. Para a secagem intermitente, o processo foi interrompido com 0,22 ± 0,03 b.s. e retomado após o período de repouso. O aumento do período de repouso diminuiu o tempo efetivo de secagem, consumo específico de energia, condutividade elétrica, danos da reação do iodo e aumentou a taxa de secagem e eficiência energética global. A secagem intermitente foi 30,25% mais eficiente que contínua.

ABSTRACT Grain drying is a common process, due to its need for the maintenance of quality, but it is the activity with the highest energy demand among the postharvest stages. Thus, this study aimed to evaluate the effect of different tempering times on the energy efficiency of drying process and maintenance of cell membrane integrity of maize grains harvested with moisture content at 0.34 ± 0.01 d.b. The grains were dried in an experimental fixed-bed dryer with control of temperature and air flow conditions. The experiment was conducted in a completely randomized design with five tempering times (0, 4, 8, 12 and 16 hours) and four repetitions, where zero corresponds to continuous drying, while the remaining times correspond to the intermittent dryings. The grains were dried at the temperature of 100 ºC and air flow of 15.4 m3 min-1 t-1 until reaching moisture content of 0.16 ± 0.03 d.b. For intermittent drying, the process was interrupted with 0.22 ± 0.02 d.b. and restarted after the tempering time. The increase of tempering time led to reductions in effective drying time, specific energy consumption, electrical conductivity and damage and increase in the drying rate and overall energy efficiency. Intermittent drying reduced the drying time, being 30.25% more efficient than continuous drying.

ABSTRACT A comparative test of water heating between the hybrid system - solar collector with heat pump - and a system with conventional supplementary heating - with high electric power - was performed. For this, a small capacity heat pump was installed, which was later installed together with a solar heating system, composed of a 250 L thermal reservoir and three thermoplastic collector plates. Tests were carried out to evaluate the COP of the heat pump and the energy consumption of the solar heating system operating with the heat pump and with an electrical resistance of 3000 W. In the laboratory tests, the heat pump presented an average COP of 2.15. In the field tests, the energy consumption of the solar system with heat pump was 54.9% lower when compared to the tests in which electrical resistance was used as a source of supplementary heating.

ABSTRACT The objective of this study is to evaluate the effect of sugarcane bagasse ash on the compressive strength and water absorption index of soil-cement bricks. The ash was sieved without chemical and/or physical treatment to reflect the use of this material in real manufacturing processes. The addition of natural ash decreased the quality of the bricks, reducing the compressive strength and increasing the water absorption index.

ABSTRACT Based on mass and energy balance equations and data collected in specialized bibliographies, it was proposed a methodology for modeling of an ice bank for thermal storage of energy at low temperature to be used in milk cooling. The data obtained by the equations arrangement were used in the design and installation of a real system, which was tested to collect data and to compare it with the estimated. The data obtained in terms of prediction of ice formation, temperature of the ice bank, water and capacity of the selected refrigeration system prove the adequacy of the equations arrangement, showing that it can be used as a tool for sizing solid ice bank in smooth pipe coils, with good approximation.

RESUMO Nesta pesquisa objetivou-se avaliar o efeito do substrato sobre a produtividade da alface cultivada em sistema aquapônico e hidropônico. A pesquisa foi realizada na Universidade Federal da Grande Dourados, localizada em Dourados, MS. Foi utilizado o delineamento em blocos ao acaso, com três tratamentos e 16 repetições. Os sistemas de cultivo foram analisados de forma independente. Os substratos analisados foram: fibra de casca de coco, espuma fenólica e vermiculita expandida. As plantas foram cultivas em dois sistemas (aquapônico e hidropônico), sendo utilizado o sistema do tipo NFT (Nutrient Film Technique). A cultura utilizada foi a alface cv. Alcione. Os parâmetros analisados foram: produtividade da cultura e porcentagem de raiz por planta. Além disso, foram realizadas análises de macronutrientes presentes nas folhas das plantas. O substrato constituído de fibra de casca de coco foi mais adequado para o cultivo de alface, uma vez que proporcionou maiores produtividades, tanto para o sistema aquapônico (2,88 kg m-2), quanto para o sistema hidropônico (2,58 kg m-2). A utilização de espuma fenólica, como substrato de cultivo, proporcionou menor média para produtividade da cultura, em ambos os sistemas de produção analisados, com valores para o cultivo aquapônico e hidropônico de 1,94 e 2,15 kg m-2, respectivamente.

ABSTRACT This study had as objective to evaluate the effect of the substrate on the yield of lettuce grown in aquaponic and hydroponic systems. The study was conducted at the Federal University of Grande Dourados, located in Dourados, MS. A randomized complete block design was used, with three treatments and 16 replicates. The cultivation systems were analyzed independently. The substrates analyzed were: coconut shell fiber, phenolic foam and expanded vermiculite. The plants were grown in two systems (aquaponic and hydroponic), using the NFT (Nutrient Film Technique) system. The crop used was lettuce cv. ‘Alcione’. The parameters analyzed were: crop yield and percentage of roots per plant. In addition, macronutrient contents were analyzed in the leaves. The substrate composed of coconut shell fiber was more suitable for lettuce production, since it led to higher yields for both aquaponic (2.88 kg m-2) and hydroponic (2.58 kg m-2) systems. The use of phenolic foam as growing substrate led to lower mean crop yields in both production systems analyzed, 1.94 and 2.15 kg m-2 for aquaponic and hydroponic systems, respectively.

Abstract This study was carried out with the objective of assessing grain yield, economic analysis and energy balance of three sunflower genotypes with and without irrigation. The experiment was installed in the Experimental Farm of the Faculty of Agrarian Sciences of the Federal University of Grande Dourados in the 2011/2012 and 2012/2013 harvests in Dourados-MS, Brazil. The experimental design used was a random complete block design with subdivisions, with and without irrigation (plots), with three genotypes (subplots) and four replications, constituting 24 plots. There were no differences in productivity among the genotypes. The irrigation increased the operational cost of the sunflower crop production, but it did not economically obstruct the activity, due to the increase of productivity of 74.5% and 30% in the harvests of 2011/2012 and 2012/2013. The energy ratios of the sunflower crop were not altered by irrigation, equal to 5.7 and 8.7 in the harvests of 2011/2012 and 2012/2013, respectively.

RESUMO No sistema de aquaponia as características dos materiais utilizados como substrato afetam diretamente no desenvolvimento das plantas, pois além de atuarem como base de sustentação, devem apresentar uma superfície para fixação de microrganismos, responsáveis pela conversão de nutrientes para formas mais facilmente disponíveis para plantas. Assim, o objetivo desta pesquisa foi avaliar o efeito de quatro substratos de cultivo sobre a produtividade da alface cultivada em sistema de aquaponia. O delineamento experimental utilizado foi em blocos ao acaso, com quatro tratamentos que corresponderam aos substratos e seis repetições. O cultivo das plantas foi realizado utilizando o sistema do tipo NFT (Nutrient Film Technique). Os substratos utilizados no experimento foram: fibra de casca de coco com brita número 3, vermiculita expandida, zeólita e espuma fenólica. O tratamento em que se utilizou espuma fenólica foi considerado o menos adequado para o cultivo da alface em sistema aquapônico, pois apresentou menor produtividade (20,8 t ha-1). O tratamento em que se utilizou fibra de casca de coco com brita número 3 foi considerado o mais adequado, uma vez que proporcionou maior produtividade (39,9 t ha-1) em relação aos demais substratos analisados.

ABSTRACT In the aquaponic system, the characteristics of the materials used as substrate directly affect plant development, because besides acting as a support base, they must present a surface to fix microorganisms, responsible for the conversion of nutrients into forms more easily available to plants. Thus, the objective of this study was to evaluate the effect of four growing substrates on the yield of lettuce grown in aquaponic system. The experimental design was randomized blocks with four treatments, which corresponded to the substrates, and six replicates. Plants were grown using the nutrient film technique (NFT) system. The substrates used in the experiment were: coconut shell fiber with crushed stone #3, expanded vermiculite, zeolite and phenolic foam. The treatment with phenolic foam was considered as the least suitable for lettuce cultivation in aquaponic system, because it caused lower yield (20.8 t ha-1). The treatment using coconut shell fiber with crushed stone #3 was considered as the most adequate, since it led to higher yield (39.9 t ha-1) compared with the other substrates analyzed.

ABSTRACT: The objective of this study was to evaluate the yield and energy balance of four sorghum genotypes in irrigated and rainfed crops. The experiment was conducted in an irrigation and drainage unit at the Federal University of Grande Dourados (UFGD), in Dourados, Mato Grosso do Sul state (Brazil). The experimental design was a randomized complete block design with split plots (with and without irrigation), testing four genotypes (BRS 506, CV 007, CV 147, and EJ 7281) with four replicates (32 plots). Irrigation provided yield increase in all four genotypes. The respective yield increases were 85.89%, 71.82%, 64.28%, and 63.36% for genotypes EJ 7281, BRS 506, CV 147, and CV 007. The energy efficiency (produced/ used ratio) was on average 3.5 under irrigation, and 2.8 for rainfed crops. These results indicate the lack of competition between sorghum and sugarcane, being the first an alternative for off-season. Irrigation increased productivity, leading to an increase in yield and, consequently, in the amount of extracted energy. Yield gains in response to irrigation were more pronounced for genotype EJ 7281. There was a positive impact of irrigation on the energy balance of the four genotypes, increasing energy efficiency.

ABSTRACT Besides cold for milk cooling, dairy facilities need to produce hot water for cleaning of tools and equipment. Overall, ohmic heating has been used in dairy farms, increasing power consumption and manufacturing costs. Therefore, as an alternative to reduce power consumption, this paper proposed a water-water heat pumping for simultaneous cold and heat generations. Accordingly, operational tests were performed with three heat-pump prototypes designed for dairy farms, in both laboratory and field levels. At laboratory, tests were carried out using electricity and CNG to define a coefficient of performance (COP). Biogas tests were performed in the field to measure its consumption. CNG average consumption was of 1.118 m3/ h, while biogas consume was of 2.02 m3 / h. COP averages of CNG driven pump were 0.20 for cooling, 0.39 for heating, and 0.59 for global. For electric-power driving, COP values were 1.75 for cooling, 2.25 for heating, and 4.00 for global. In addition to evaporating and compensating temperatures, engine rotation was one factor of influence on heat-pump performance.

ABSTRACT This study consisted of designing and building an experimental dryer that allows working with different temperatures and velocities of the air, aiming to perform studies on thin- and thick-layer drying of agricultural products. The project was divided into three stages: heat source designing, dryer geometric parameters, and fan selection to meet operational demand. Heating was made by a set of six electrical resistances totaling 12 kW and the drying bed in thin layer was composed of two trays with diameter of 0.20 m. Operational demands were met using a centrifugal fan with a power rating of 735.5 W. The used methodology was able to size the experimental dryers for thin- and thick-layer drying working at distinct temperatures and air velocities.

RESUMO A integração entre a criação de peixes em sistema intensivo e a produção vegetal, denominada “aquaponia”, é praticada com sucesso em países como Estados Unidos, Austrália e também, na Europa. No Brasil, essa integração vem atraindo a atenção de pesquisadores e produtores. Nesse contexto, o objetivo deste trabalho foi avaliar o efeito de dois substratos (pedra brita número 3, PB3 e espuma flexível de poliuretano, EFP) sobre a produção de alface aquapônica, além disso, demonstrar que a água residuária proveniente da produção intensiva de tilápia proporciona características qualitativas suficientes para produção competitiva de alface sem adição de fertilizantes comerciais. O tratamento onde foi utilizada EFP proporcionou maiores concentrações de macro e micronutrientes na parte aérea das plantas, maior produção de massa fresca da parte aérea (95,48 g planta-1) e maior número de folhas (14,90) em relação à PB3. Esses resultados foram atribuídos ao menor estresse pós-transplantio e ao maior tempo de retenção de água proporcionado pela EFP. A água residuária proveniente da criação intensiva de tilápia pode fornecer nutrientes suficientes para produção de alface, não sendo necessário complementação da fertilização com produtos comerciais. Assim, a EFP apresenta condições mais adequadas para ser utilizada como substrato, em sistema aquapônico, com recirculação de água residuária proveniente da criação intensiva de tilápia.

ABSTRACT The integration of fish farming in intensive system and plant production, called "aquaponics" is practiced successfully in countries like the USA, Australia and Europe. In Brazil, this integration has attracted the attention of researchers and producers. In this context, the aim of this study was to evaluate the effect of two substrates (crushed stone number 3, CS III and flexible polyurethane foam, FPF) on the production of aquaponic lettuce, moreover, to show that the residual water from intensive tilapia production provides sufficient qualitative characteristics for competitive production of lettuce without adding commercial fertilizers. The treatment in which FPF was used provided higher concentrations of macro and micronutrients in the shoots, higher production of fresh matter of shoots (95.48 g plant-1) and a larger number of leaves (14.90) relative to CS III. These results were attributed to the lower post-transplanting stress and the higher water retention time provided by the FPF. The residual water from tilapia intensive farming can provide sufficient nutrients for the production of lettuce, making the supplementary fertilization with commercial products unnecessary. Thus, the FPF presents the most suitable conditions to be used as substrate in aquaponics system with recirculation of the residual water from the intensive tilapia farming.

RESUMO A biomassa polidispersa tem como uma de suas principais características as variações das dimensões e dos formatos de suas partículas. Os métodos de determinação do diâmetro médio por peneiramento, amplamente utilizados devido a sua relativa simplicidade e baixo custo, quando aplicados a materiais heterogêneos, como a biomassa polidispersa, podem levar a resultados equivocados. Assim, com o objetivo de obter resultados mais precisos, foram avaliados três métodos de determinação do diâmetro médio de partículas de biomassa polidispersa, baseados na técnica de fracionamento por peneiramento mecânico: um de forma analítica (Diâmetro de Sauter) e outros dois por meio de análise gráfica das funções de distribuição das partículas (Função de Densidade de Distribuição Mássica e Função Cumulativa/Aumentativa de Distribuição). O método baseado na análise gráfica da função da distribuição da densidade mássica (FDDM) foi o mais eficiente para a análise do bagaço de cana, pois permitiu identificar as diferentes populações existentes e identificar com clareza as dimensões características, mostrando assim ser uma poderosa ferramenta para a análise granulométrica de biomassas polidispersas.

ABSTRACT Polydispersed biomass has as one of the main features variations in particle dimension and size. Mean diameter determination methods by screening are widely used due to their relative simplicity and low cost. However, when applied for heterogeneous materials such as polydispersed biomass, they can lead to misleading results. Thus, we evaluated three methods for determining mean diameter of polydispersed biomass particles, aiming at most accurate results. The methods are based on size fractionation by mechanical sieving: one analytical (Sauter diameter) and two by graphical analysis of particle distribution functions (Mass Distribution Density - MDD and Cumulative/ Augmentative Distribution - CAD). The method based on graphical analysis of mass distribution density (MDD) was the most efficient for sugarcane bagasse analysis, once it enabled detecting different populations and clearly identifying their respective characteristic dimensions. Therefore, it is a powerful tool for particle size analysis of polydispersed biomass.